Weberset SPF White 20kg

Weberset SPF Tile Adhesive is a flexible, cement-based polymer modified tile adhesive for internal & external use, suitable for use with underfloor heating. It is suitable for use with substrates subject to movement or expansion and is high-grab — non-slip for walls and floors. Weberset SPF Tile Adhesive is available in grey or white, supplied in 20kg bags. Weberset SPF Tile Adhesive has extended open time for internal and external use and is suitable for fixing all types of ceramic wall and floor tiles, mosaics, marble, terrazzo, natural stone, brick slips and glass blocks in areas that will be dry or wet. It is particularly suited for situations where some movement, deflection or limited shrinkage is likely. Weberset SPF Tile Adhesive is best suited for fixing ceramic or porcelain tiles, on to most common substrates: • Walls and floors• Interior and exterior situations• Underfloor heating• Undertile warming• Overboarded wooden floors• Low porosity tiles or substrates• Power-floated screeds• Tiling onto existing tiles Constraints: Weberset SPF Tile Adhesive is not recommended for tiling onto single layer wooden floors, e.g. chipboard, tongued and grooved timber. Not recommended for tiles with resin backs. Please contact technical services for application advice. Preparation:Prior to using Weberset SPF Tile Adhesive ensure that all surfaces are clean, dry, sound and free from dust, grease or any contaminating barrier. Make good any unsound areas and remove flaky or peeling layers before tiling. Prime porous or dusty surfaces. Weber PR360 is normally recommended for most walls in dry areas. Weber AD250 is recommended for wood, wet areas and floors. Allow the primer to dry. Check before use that the colour of the adhesive does not cause staining or discolouration of light coloured or translucent tiles. Technical Data:Bed thickness: 3 – 6mm (may be exceeded in small areas only)Coverage (approx.): 9 kg/m2 (solid bed, 6 mm thick), 4.5 kg/m2 (solid bed, 3 mm thick), 3.0 kg/m2 (using a notched trowel with 6 x 6 mm notches at 12mm centres)Open time: 30 minutesWorking time (pot life): 1 hour after mixingSet time: 24 hours – light foot traffic, full load after 48 hoursTemperature resistance: –10°C to 100°C and frost resistant when setWater addition: 5 litres per 20kgParticle size: Up to approx. 0.5mm

Italian Design Intarsi Vinci 60cm x 120cm Wall & Floor Tile

The Price Displayed Above is Per Tile. Colour: Black/White Material: Porcelain Finish: Satin 3-D Honed (Rectified) Size (cm): 60cm x 120cm Thickness (mm): 10mm Suitability: Wall & Floor N° of Tiles per Square Metre (m2): 1.38  N° of Tiles per Pack: 2 Availability: In Stock

Italian Design Intarsi Warm Gala 60cm x 120cm Wall & Floor Tile

The Price Displayed Above is Per Tile. Colour: Black/White Material: Porcelain Finish: Satin 3-D Honed (Rectified) Size (cm): 60cm x 120cm Thickness (mm): 10mm Suitability: Wall & Floor N° of Tiles per Square Metre (m2): 1.38  N° of Tiles per Pack: 2 Availability: In Stock

Slow Set White Easiflex White 20kg Full Pallet Deal - 54 Bags

This is a full pallet deal for 54 bags   Colour: White Size (kg): 20kg Suitability: Fixing ceramic tiles, mosaics, marble and natural stone to solid impermeable floors and 15mm ply-wood overlay

Slow Set White (Easiflex) 20kg

Palace Easi-flex is a standard (slow) setting cement based flexible tile adhesive, shown here in Grey. Use this adhesive to fix to any substrate but especially for use on areas where some movement can occur such as secured plywood, backer-board or timber panels.  This white tile adhesive is ideal for use with light coloured natural stone such as travertine and limestone to prevent shadowing and also for use on whitelight wall or floor tiles to prevent joint overspill showing through joints, also ideal for fixing glass tiles and prevent the adhesive showing through the backing. Easi-flex forms a strong bond with concrete, cement, concrete block-work and brickwork giving improved flexural strength, and also is suitable where under-floor heating is installed. It is sufficiently water-resistant to be suitable for interior / exterior use, in swimming pools and locations which are subject to persistent dampness, e.g. showers, saunas, wet rooms and bathrooms. The manufacturers coverage guidelines state that 20kg will cover approximately 5m2 on a floor, when using a 10mm notched trowel.